Knight Riderz Sequential LED Light Bar with Flashing Brake Alert
* Warranty does not apply to failure due to improper installation or abuse or misuse of product.
We look forward to serving you.
We Accept:
Copyright ©2008-09 WYKED ILLUZIONZ ™
Call today 301-639-9273
For your motorcycle and other vehicle detailing needs, please visit our sister-company,
"WE TAKE PRIDE IN YOUR RIDE"
"WE TAKE PRIDE IN YOUR RIDE"
Knight Riderz Sequential LED Light Bar with Flashing Brake Alert
Knight Riderz Sequential LED Light Bar with Flashing Brake Alert
This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum visibility. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your exiting brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high.
Item: LB02
Sale $26.95 each
Knight Rider Non-Sequential LED Light Bar with Flashing Brake Alert
This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum viability. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your exiting brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high.
Item: LB03
Sale $26.95 each
Knight Rider Non-Sequential LED Light Bar with NON Flashing Brake Alert
Not into the sequential or flashing LEDs, this light bar is for you. This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will then go to full intensity mode. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Simply connect the black wire to any ground wire, the Red wire to your exiting brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 4.7" long x .7" wide x .7" high. These lights bars can be used as running, brake, and turn when used in conjunction with one of our controllers.
Item: LB01
Sale $24.95 each
Knight Rider LED License Plate Frames
Knight Rider LED License Plate Frames
Choice of Brilliant Chrome or Black Power Coat License Plate Frame
Choice of Sequential or Non Sequential Knight Rider LED Light Bars (LB01, LB02, or LB03)
Mounting Hardware Included
Optional White LED License Plate Illuminator Bolts
Dimensions: - will fit most states license plates (7-3/16" x 4-1/4"), except Maryland
Sequential Light Bar: This light bar contains 12 high power intensity LEDs. In running light mode the LEDs sequence from side to side in a "Knight Rider" sequence. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum viability. Simply connect the black wire to any ground wire, the Red wire to your exiting brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required.
Non Sequential Light Bar: This light bar contains 12 high power dual intensity LEDs. In running light mode the LEDs are on in low intensity mode. When the brake is applied the LED will flash for approximately 5-6 seconds then go to a solid on state until the brake is released. Both modes, running and brake, have been designed to create the maximum viability. Simply connect the black wire to any ground wire, the Red wire to your exiting brake light wire and the blue wire to an existing running light power source. Works with any 12VDC system, no load equalizer or resistors required.
Knight Rider LED License Plate Frame
Sequential Light Bar
Item: LB04
Sale $59.95 each
Knight Rider LED License Plate Frame
NON Sequential Light Bar
Item: LB04_NS
Sale $59.95 each
Chrome LED Tag Bolts
Includes washers, nuts and wrench
Item: TB01C
Sale $16.95 pair
Knight Riderz Sequential LED Light Bar with Flashing Brake Alert
Knight Rider LED License Plate Frames
Knight Rider Non-Sequential LED Light Bar with Flashing Brake Alert
Knight Rider Non-Sequential LED Light Bar with NON Flashing Brake Alert
Knight Rider LED License Plate Frames
New Longer 21 LED Knight Riderz
Knight Rider Sequential 21 LED Light Bar with Flashing Brake Alert -
RED
Item: LB22
Price: $39.95 (each)
Knight Rider Sequential 21 LED Light Bar with Flashing Brake Alert -
Smoked
Item: LB22S
Price: $39.95 (each)
Works with any 12VDC system, no load equalizer or resistors required. Dimensions: 7.5" long x .7" wide x .7" high.
Available in
Red
or
Smoked
.
Knight Rider Sequential 12 LED Light Bar with Flashing Brake Alert
Knight Rider Sequential 12 LED Light Bar with Flashing Brake Alert -
Blue
For Off Road or Show Use Only
Item: LB06
Sale $26.95 each
Knight Rider Sequential 12 LED Light Bar with Flashing Brake Alert
New Longer 21 LED Knight Riderz
Knight Riderz Strobe
Knight Riderz Strobe - Red
Our new LB07 light bar contains 12 high power Single intensity LEDs. There are three built in strobe patterns that will demand attention from anyone behind your vehicle. There is a constant strobe pattern, a double beat and a quad beat pattern, check out the video. When the brake is applied the LED will strobe based on what pattern you have selected. The unit comes pre-taped with 3M double sided tape for easy mounting to any flat surface. Works with any 12VDC system, no load equalizer or resistors required.
Dimensions: 4.7" long x .7" wide x .7" high. Available in Red.
Item: LB07
Price: $26.95 each
Knight Riderz Strobe